Leading North America Supplier - 20 Years of Innovation - Shipping Globally
GAO-SFPCB-106
GAO-SFPCB-106

GAOTek SFP CWDM BIDI Transceiver with 1.25Gb/s (40km)

USD Call for Quote

Overview

This 1.25 Gbps SFP CWDM BIDI transceiver is used with Single-mode fiber to span up to 24.8 Miles (40Km). This Bi-Directional Coarse Wavelength Division Multiplexing Small Form-Factor Pluggable (SFP CWDM BIDI)provide an unique enhanced digital diagnostic monitoring interface which provide real time access to important device parameters and a sophisticated alarm system. The Transmitter section uses a DFB Laser transmitter and PIN photo-detector .These transceivers comply with SFF 8472 and RoHS standards. It is a Class 1 Product which comply with the requirements of IEC 60825-1 and IEC 60825-2.

Key Features

  • Compliant with SFF-8472, ROHS and lead free
  • Class 1 Product which comply with the requirements of IEC 60825-1 and IEC 60825-2
  • Up to 8 Miles (40Km) on 9/125µm SMF
  • Up to 1.25Gb/s data links
  • DFB laser transmitter
  • PIN photo-detector
  • Hot-pluggable SFP footprint
  • BIDI LC/UPC type pluggable optical interface
  • Support Digital Diagnostic Monitoring interface
  • Single + 3.3V Power Supply
  • Low power dissipation
  • Metal enclosure, for lower EMI
  • Case operating temperature range from 32°F to +158°F( 0°C to +70°C) for Commercial use

Technical Specifications

Protocol 2-wire serial communication protocol
Standard Class 1 Product which comply with the requirements of IEC 60825-1 and IEC 60825-2.

SFF-8472

ROHS-6

IEC/EN 61000-4-2

FCC Part 15 Class B EN 55022 Class B (CISPR 22A)

IEC/EN 60950 ,UL

EN61000-3

Working Range Up to  24.8 Miles (40Km)
Data rate 1.25 Gb/s
Wavelength CWDM
Transmitter Extinction Ratio 9 dB
Transmitter Off Output Power -45dBm
Transmitter Differential Line Input Impedance 90-110 Ω
Receiver Sensitivity -24dBm
Receiver Input Saturation Power(Overload) -1 dBm
Supply Voltage -0.5 to 4V
Dimensions 2.29in*0.54in*0.33 in                                               (L  58.4mm*W 13.9mm*H 8.5mm)
Storage Ambient Humidity 5% to 95%
Storage Temperature -40°F to 185°F (-40°C to 85°C)
Case Operating Temperature 32°F to +158°F( 0°C to +70°C)

Product Selection

Wavelength Clasp Color code
1270 nm Gray
1290 nm Gray
1310 nm Gray
1330 nm Purple
1350 nm Blue
1370 nm Green
1390 nm Yellow
1410 nm Orange
1430 nm Red
1450 nm Brown
1470 nm Gray
1490 nm Purple
1510 nm Blue
1530 nm Green
1550 nm Yellow
1570 nm Orange
1590 nm Red
1610 nm Brown

PIN Descriptions:

Notes:

  1. Circuit ground is internally isolated from chassis ground.
  2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS<0.8V
  3. Should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V.MOD_DEF (0) pulls line low to indicate module is plugged in.
  4. This is an optional input used to control the receiver bandwidth for compatibility with multiple data rates (most likely Fiber Channel 1x and 2x Rates).If implemented, the input will be internally pulled down with > 30kΩ resistor. The input states are:
  • Low (0 – 0.8V): Reduced Bandwidth
  • (>0.8, < 2.0V): Undefined
  • High (2.0 – 3.465V): Full Bandwidth
  • Open: Reduced Bandwidth
  1. LOS is open collector output should be pulled up with 4.7k – 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.

Electrical Interface Characteristics:

Note (1): A (TX) + B (RX) = 280mA (Not include termination circuit)

Digital Diagnostic Functions

GAOTek GAO-SFPCB-106 transceivers support the 2-wire serial communication protocol as defined in the SFP MSA. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information.

Additionally, GAOTek SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage .It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range.

The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement.

The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.

Digital diagnostics for the GAO-SFPCB-106 are internally calibrated by default.

Recommended Circuit Schematic

Regulatory Compliance

Mechanical Specifications

Applications

  • Switch to Switch Interface
  • Gigabit Ethernet
  • Switched Backplane Applications
  • Router/Server Interface
  • Other Optical Links

Questions from our customers

There are no questions yet. Be the first to ask a question about this product.

Only registered users are eligible to enter questions