Description
Overview
GAOTek dual channel signal generator can generate sine wave, square wave, triangle wave, pulse wave, and arbitrary wave etc. The frequency will be up to 40MHz. And it has duty-cycle correction, amplitude modulation function and frequency sweep function, etc. It can show output signal, amplitude and frequency at the same time. This series has amplitude frequency characteristics, and the appearance is very delicate and beautiful. It can be applied in factories, schools, research institutes and laboratories. The main difference is the max output frequency of sin wave.
Technical Specifications
| Sine frequency range | JDS6600-15M 0 MHz to 15 MHz, JDS6600-30M 0 MHz to 30 MHz, JDS6600-40M 0 MHz to 40 MHz, JDS6600-50M 0 MHz to 50 MHz |
| Triangle frequency range | JDS6600-15M 0 MHz to 15 MHz, JDS6600-30M 0 MHz to 15 MHz, JDS6600-40M 0 MHz to 15 MHz, JDS6600-50M 0 MHz to 15 MHz |
| Pulse frequency range | JDS6600-15M 0 MHz to 6 MHz, JDS6600-30M 0 MHz to 6 MHz, JDS6600-40M 0 MHz to 6 MHz, JDS6600-50M 0 MHz to 6 MHz |
| Square rise time | JDS6600-15M ≤30 nS, JDS6600-30M ≤25 nS, JDS6600-40M ≤20 nS, JDS6600-50M ≤20 nS |
| Minimum Frequency resolution | 0.01 µHz (0.00000001 Hz) |
| Frequency accuracy | ±20 ppm |
| Frequency stability | ±1 ppm or 3 h |
| Waveform | Sine, Square, Triangle, Pulse (duty-cycle correction), Partial Sine, CMOS, DC level, Half-wave, Full-Wave, Post-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Since Pulse, Lorentz Pulse, and 60 kinds of user defined waveform. |
| Waveform length | 2048 points |
| Waveform vertical resolution | 12 bits |
| Sine | Harmonic suppression ≥45 dBc(<1 MHz), ≥40 dBc (1 MHz to 20 MH, Total harmonic distortion <0.8% (20 Hz to 20 kHz, 0 dBm) |
| Square and Pulse | Overshoot (Square) ≤5%, Duty-cycle range (Pulse) 0.1% to 99.9% |
| Ramp wave | Linearity ≥98% (0.01Hz to 10kHz) |
| Amplitude resolution | 1mV |
| Amplitude stability | ±0.5% or 5 h |
| Amplitude flatness | ±5% (<10 MHz), ±10% (>10 MHz) |
| Output impedance | 50 ohms ±10% (typical) |
| Protection | All the signal output terminal can be shorted within 60 s |
| Offset resolution | 0.01 V |
| Phase adjusting range | 0° to 359.9° |
| Phase resolution | 0.1° |
| Low level | <0.3 V |
| High level | 1 V to 10 V |
| Level rise or fall time | ≤20 ns |
| Frequency measurement range | 1 Hz to 100 MHz |
| Measurement accuracy | Gate time continuously adjusted between0.01s |
| Counting region | 0 to 4294967295 |
| Coupled mode | 2 kinds Coupling modes, DC and AC |
| Control mode | Manual operation |
| Input signal voltage range | 2 Vpp to 20 Vpp |
| Pulse width measurement | 0.01 us (resolution), 20 s (MAX measuring time) |
| Period measurement | 0.01 us (resolution), 20 s (MAX measuring time) |
| Sweep channel | CH1 or CH2 |
| Sweep type | linear sweep, log sweep |
| Sweep time | 0.1 s to 999.9 s |
| Setting range | User settings |
| Sweep direction | Forward, Backward and Roundtrip |
| Number of pulses | 1 to 1048575 |
| Burst mode | Manual Trig, CH2 Trig, Ext. Ring (AC), Ext. Ring (DC) |
| Display | 2.4 in (6.096 cm) TFT colour LCD |
| Storage and loading | Quantity 100 groups, Location 00 to 99 (Power on will load the position |
| Arbitrary wave | 1 to 60, totally 60 groups |
| Power supply | DC5V±0.5V |
| Manufacturing process | Surface-mount technology, FPGA design, high reliability, long service life |
| Buzzer | User can set ON or OFF by procedure |
| Operating characteristics | Full button operation, knob continuous adjustment |
| Environmental conditions | Temperature 32 °F to 104 °F (0 °C to 40 °C), humidity <80% |