GAOTek Separate Type Thickness Meter (High Accuracy, Micro Coating)

Additional Information

Standard accessories:

• Carrying case -1 pc.
• Operation manual -1 pc.
• F probe -1 pc.
• Calibration foils -1 set.
• Substrate (Iron) 1 pc.

Optional accessories:

• USB, RS-232C cable & software.
• Bluetooth data output & software

Front Panel Descriptions

3-1 Jack forRS232C
3-2 Display
3-3 Plus Key
3-4 Single/Continuous Key
3-5 Minus Key
3-6 Zero Key
3-7 Power Key
3-8 Probe

MEASURING PROCEDURE

1. Press the power key to switch on the power and ‘0’ displays on the Display. The gauge will restore the last operation on display itself, with ‘Fe’ symbol showed on Display.
2. Press the probe on a coating layer to be measured. The reading on the display is the thickness of the coating layer. The reading can be corrected by pressing the Plus key and minus key while the probe is away from the substrate or the measured body.
3. To take the next measurement, just lift the probe to more than 1 centimeter and then repeat the step above.
4. If suspecting the accuracy of measurement, you should calibrate the gauge before taking the measurements. For the calibration procedures, please refer to the calibration part.
5. The gauge can be switched off by pressing the Power key. On the other side, the gauge will power itself off about 50 seconds after the last operation.
6. To change the measurement unit ‘μm’ or ‘mil’ by depressing Power key and not releasing it till ‘UNIT’ on the Display and then pressing Zero key (3-6).
7. To change measurement mode from the single to continuous or vice visa, just by
   Depressing the Single/Continuous Key.
   Depressing Power key and not releasing it till ‘SC’ on the Display and then pressing Zero key (3-6). The measurement mode is the continuous mode if a symbol ‘’never disappears on the display. Otherwise it is in a single measurement mode if ‘ ’ only appears for a while every time taking a measurement.

CALIBRATION

1. Zero adjustment Take the iron substrate. Place the probe (3-8) on the substrate steadily. Press the zero key (3-6) and ‘0’ will be on the Display before lifting the probe. If by pressing the ZERO key, but the probe is not placed on the substrate or an uncoated standard, the zero adjustment is invalid.
2. Select an appropriate calibration foil according to your measurement range.
3. Place the standard foil selected onto the substrate or the uncoated standard.
4. Place the sensor (3-8) mildly onto the standard foil and lift. The reading on the display is the value measured. The displayed reading value can be adjusted by pressing the plus key (3-3) or minus key (3-5) while the probe is away from the substrate or the measured body.
5. Repeat step 4 until the result is correct.

BATTERY REPLACEMENT

When it is necessary to replace the battery, the battery symbol ‘ ‘ will appear on the Display.

• Slide the Battery Cover away from the instrument and remove the batteries.
• Install the batteries (4 x 1.5 V AAA / UM-4) correctly into the case.
• If the instrument is not to be used for any extended period, remove batteries.

CONSIDERATIONS

1. In order to weaken the influence of the measured material on the accuracy of measurement, it is recommended that the calibrations should be done on the uncoated material to be measured.
2. Probes will eventually wear. Probe life will depend on the number of measurements taken and how abrasive the coating is.

RESTORE FACTORY SETTINGS

When to restore?

It is recommended to restore factory settings in the one of following cases.

• The gauge does not measure any more.
• Measurement accuracy is degraded caused by environmental conditions change greatly.

How to restore?

Depress Power key and not release it till ‘CAL’ appears on the Display. It is about 12 seconds from starting to depress Power key.

When F:H is on Display, lift the probe to more than 5 centimeters, then press the Zero key again and the gauge return to measurement state. The factory setting is restored. Remember, to restore factory setting should be done within 6 seconds at every stage or the gauge will quit itself and restoration is invalid.

Notes

1. Settings include restoring factory setting, unit setting, S/C setting, which should be done within 6 seconds at every stage, or the gauge will quit itself and keep its status before.
2. It is strongly recommended that no changes should be made to the value of Ln controlled by Power key. It takes about 14 seconds from starting depressing Power key. Its value can be changed by plus/minus key after displaying Ln and releasing the power key. Store its value and quit by pressing Zero key) which will seriously affect the accuracy. Its value can be adjusted by professional persons only under the cases of replacing a new probe or making the gauge more accurate. Generally, larger the value of Ln smaller will be the reading on a same thickness. A little variation of value of Ln will cause a great change in reading at high end. The rules to adjust the value of Ln are as follow:

• Reading at low end can be adjusted to the exact value by the plus or minus key.
• To enlarge the Ln if reading at low end is ok but reading at high end is too large. On the contrary, to decrease the Ln if reading at low end is ok but reading at high end is too small.
• Repeat procedures from A to B till the readings on the every standard foil are satisfying the accuracy.