Below are general answers on how to operate, maintain, and calibrate a structural thermal imager and industrial endoscope from the list of GAO Tek’s structural thermal imagers and industrial endoscopes. To facilitate our customers to a selection of our products, we have further classified our structural thermal imagers and industrial endoscopes by their features:  handheld, high-resolution, multi-application, outdoor, rugged and wireless.

We have products in stock and can ship overnight to most places in the U.S. and Canada.

If you have any questions about our products or want to place an order, our technical experts can help you. Please fill out this form or email us.

 

Operating a Structural Thermal Imager:

Pre-Operation Checks:

  • Inspect our thermal imager for any physical damage or defects.
  • Ensure that the battery is adequately charged or that a power source is available.
  • Verify that the thermal imager’s lens is clean and free from debris.

Power On/Off:

  • Follow GAO Tek’s instructions to power the thermal imager.
  • Allow the imager to go through any startup procedures.
  • Power off the device following GAO Tek’s recommended procedure.

Calibration:

  • Some thermal imagers require periodic calibration. Follow the GAO Tek’s guidelines for calibration procedures.
  • If the imager has an automatic calibration feature, ensure it is enabled.

Image Capture:

  • Point our thermal imager towards the area of interest.
  • Adjust settings such as temperature scale, emissivity, and focus if needed.
  • Capture thermal images or videos according to the application requirements.

Data Analysis:

  • Review captured thermal images on the imager’s display or transfer them to a computer for in-depth analysis.
  • Identify and analyze temperature variations or anomalies.

Documentation:

  • Record and document the findings, including the location and temperatures of anomalies.

 

Maintaining a Structural Thermal Imager:

Cleaning:

  • Clean the thermal imager lens and body using GAO Tek’s recommended cleaning solutions.
  • Handle the device carefully to prevent scratches or damage to the lens.

Battery Maintenance:

  • If the thermal imager uses batteries, regularly check and recharge or replace them as needed.
  • Follow GAO Tek’s guidelines for battery maintenance.

Inspection:

  • Periodically inspect the device for signs of wear, damage, or malfunction.
  • Ensure that buttons, switches, and the display are functioning correctly.

Firmware Updates:

  • Check for and install firmware updates provided by GAO Tek to enhance performance and add new features.

 

Calibrating a Structural Thermal Imager:

Calibration Frequency:

  • Calibrate the thermal imager according to GAO Tek’s recommendations.
  • Regular calibration is essential to maintain accuracy.

Blackbody Calibration:

  • If the thermal imager supports external blackbody calibration, use a stable heat source to calibrate the device.
  • Follow the specific procedures outlined in GAO Tek’s user manual.

Verification:

  • Perform a verification check using a known temperature reference to ensure accurate temperature readings.
  • Adjust calibration settings if necessary.

Documentation:

  • Document the calibration process, including dates, reference standards used, and any adjustments made.
  • Keep calibration records for compliance and auditing purposes.

 

Operating an Industrial Endoscope:

Pre-Operation Checks:

  • Inspect our industrial endoscope for any damage or defects.
  • Ensure that the insertion tube and camera lens are clean and free from debris.
  • Check the battery or power source for sufficient charge.

Power On/Off:

  • Power on the endoscope following GAO Tek’s instructions.
  • Verify that the display unit or connected device is functioning properly.
  • Power off the device following the recommended procedure.

Insertion and Navigation:

  • Insert the endoscope into the inspection area.
  • Navigate through the area using the control knobs or joystick.
  • Adjust illumination settings if necessary.

Image Capture:

  • Capture images or videos of the inspection area.
  • Record any findings or anomalies observed during the inspection.

Data Analysis:

  • Review captured images or videos on the display unit or transfer them to a computer for further analysis.

Documentation:

  • Document the inspection findings, including the location and nature of any issues.

 

Maintaining an Industrial Endoscope:

Cleaning:

  • Clean the camera lens, insertion tube, and other components using recommended cleaning solutions.
  • Follow proper hygiene practices to avoid contamination.

Storage:

  • Store our endoscope in a protective case when not in use to prevent damage.
  • Ensure that our device is stored in a dry and cool environment.

Cable Inspection:

  • Periodically inspect the insertion tube and cables for any signs of wear or damage.
  • Replace damaged parts as needed.

 

Calibrating an Industrial Endoscope:

Calibration Frequency:

  • Calibrate the endoscope as recommended by GAO Tek.
  • Calibration intervals may vary based on usage and environmental conditions.

Camera Calibration:

  • If the endoscope allows for camera calibration, use calibration targets provided by GAO Tek.
  • Follow the specific calibration procedures outlined in GAO Tek’s user manual.

Verification:

  • Verify the image quality and color accuracy after calibration.
  • Adjust calibration settings if necessary.

Documentation:

  • Document the calibration process, including dates, calibration standards used, and any adjustments made.

Keep calibration records for compliance and auditing purposes.