Click to enlarge
GAOTek Infrared Thermometer with Data Hold (High Accuracy)
Back to products
Ion Meter for Bromide Ion (Multiple Concentration Units)

GAOTek Infrared Thermometer with Auto Power Off (Light Weight)

This Infrared Thermometer with Auto Power Off (Light Weight) is a non-contact temperature tester to measure the object’s surface for the temperature ranges from 392 °F~3002 °F (200 °C~1650 °C).

Add to quote
SKU: GT00YT00ZB Categories: , , , , , , ,
Description

Description

Overview

GAOTek Thermometer with Auto Power Off (Light Weight) is a non-contact temperature tester to measure the object’s surface for the temperature ranges from 392 °F~3002 °F (200 °C~1650 °C).This device consists of optics system, temperature sensor signal amplifier, processing circuit and a LCD display. The optics collect the infrared energy emitted by object and focus onto the sensor. Then the sensor translates this energy into an electric signal which is displayed in digital format on the LCD by the signal amplifier and the processing circuit.

Key Features

  • Non-contact design
  • Suitable for industrial temperature test
  • Data store recall function
  • High and low temperature alarm setup function
  • Data hold function
  • °C / °F selection
  • Laser target point ON/OFF selection
  • Backlight ON/OFF selection
  • Auto power off
  • Low battery indication

Technical Specifications

Temperature Range 392 °F ~ 3002 °F (200 °C ~ 1650 °C)
Accuracy ±2.7 °F (±1.5 °C) or ±1.5 % whichever is greater
Resolution 0.1 °F or 0.1 °C
Repeatability 1% of reading or 1 °C
Response Time 500 ms, 95% response
Spectral Response 8 µm -14 µm
Emissivity 0.10~1.00 Adjustable (0.95 preset)
Distance to Spot Size 50:1
Operating Temperature 32 °F ~ 104 °F (0 °C ~ 40 °C)
Operating Humidity 10 % – 95 %RH non-condensing, up to 86 °F (30 °C)
Storage Temperature -4 °F ~ 140 °F (-20 °C ~ 60 °C)
Power 9 V Alkaline or NiCd battery
Battery Life (Alkaline) Non-laser mode: 22 hrs;

Laser models: 12 hrs
Dimension 5.55 in × 2.36 in × 7.87 in (141 mm × 60 mm × 200 mm)
Weight  0.59 lbs (270 g)

Additional Information

LCD display & buttons

LCD display

A.Measuring reading
B.Measuring unit
C.Laser on icon
D.Back light on icon
E.Battery power icon
F.Scanning icon
G.Data hold icon
H.Mode/Emissivity indicator
I.Data storage/read icon
J.Low temperature alarm icon
K.High temperature alarm icon

Operation
Operating the unit

  1. Open the battery door and insert a 9 V battery properly.
  2. Pull the trigger to turn on the
  3. Aim at the target surface and pull the trigger, then temperature will be shown on the LCD.
    This unit is equipped with a laser, which is only used for aiming.

Locating a Hot Spot

To find a hot spot, aim the thermometer outside the area of interest, then scan across with an up and down motion until you locate the hot spot.

Distance to Spot size

  1. When taking measurement, pay attention to the Distance to Spot Size. As the Distance (D) from the target surface increases, the spot size (S) of the area measured by the unit becomes larger.The Distance to Spot size of the unit is 50:1.This unit is equipped with a laser, which is used for aiming.
  2. Field of view:
    Make sure the target is larger than the unit’s spot size. The smaller the target the closer measure distance.When accuracy is critical, make sure the target is at least twice as large as the spot size.

Diagram description

(1) Trigger: Turn on LCD display VERXX software version for 1 sec. And turn to display reading with SCAN icon. Release the trigger, display reading with HOLD icon. Built in auto power off in 30 sec.
(2) Laser/back light button: When back light is turned on, back light will remain on for any operation for 10 sec. LCD indicate on/off status.
(3)-(6) Key functions: press 3 key, LCD sub display blinks MAX-MIN-DIF-AVG-HAL-LAL-STO-EMS segment (only main display means normal measuring mode), press 4 key to enter.

  • MAX: measuring maximum temperature
  • MIN: measuring minimum temperature
  • DIF: Basic on the reading before press 4 key, compute the difference of current
  • AVG: measuring average temperature
  • HAL: high temperature alarm–when selected HAL, press 5 keys to set high temperature alarm trigger and confirm by pressing 4 key. When reading over trigger, LCD displays HI icon with BiBi audio
  • LAL: low temperature alarm–when selected LAL, press 5 keys to set low temperature alarm trigger and confirm by pressing 4 When reading over trigger, LCD displays LOW icon with BiBi audio sounds.
  • STO: data storage–when selected STO, lock & DATA & 1—indicator will show when press 4 key. After temperature read out, press 6 key to store, then 2— memory unit will be shown. There 12 groups memory unit available. To recall the stored data in normal measuring mode, press 6 key; remove all data by pressing 6 keys for 3
  • EMS: Emissivity setup– press 5 key for emissivity settings, press 4 key to save setup and back to normal

(7) Celsius/ Fahrenheit switch: Please open battery and push the slide switch for conversion.

Maintenance:

  1. Lens Cleaning:
    Blow off loose particles using clean compressed air. Gently brush remaining debris away with a moist cotton swab. The swab may be moistened with water.
  2. Case cleaning:
    Clean the case with a damp sponge/cloth and mild soap.

Note:

  1. Do not use solvent to clean plastic lens.
  2. Do not submerge the unit in water.