Ethernet Media Converters
GAO Tek’s fast fiber converters are appropriate for all businesses and service provider applications. They offer an inbuilt processor that persistently screens both the copper and fiber connections. Fast fiber converters are useful for the most part referred to as “Link Pass-Through”, where it screens the conditions of the connection to the end gadgets and which guarantees that every end-point knows whether the whole connection is active or not. A few fiber converters essentially join the connection despite the fact that the remote copper gadgets might be down or if the fiber link is broken. GAO Tek’s converters are easy to setup and install. These compact and value-conscious fiber converters feature auto-switching MDI and MDI-X supporting on the RJ45 UTP connections as well as manual control for UTP mode, speed, full and half duplex, and LFPT (link fault pass-through).
GAO Tek’s fast fiber converters connect UTP coppers to fibers. They give a conservative way to develop the separation of a current system. The devices provide a simple solution for connecting Ethernet networks to remote locations using multi-mode fibers while delivering solid network performance and scalability. Fast fiber converters provide connectivity to users or network segments that are in isolated areas. They connect traffic control or monitoring systems at extreme distances to the main office. Fast fiber converters can also extend network connectivity to remote areas of stadiums, auditoriums or other venues.
GAO Tek’s fast fiber converters are noticed for their simplicity such as non-management features, guaranteed reliability, and extremely affordable cost. They also provide stable operation in harsh industrial environments. Designed under IEEE 802.3u, 10/100 Base-TX and 100 Base-FX standards, these devices support full wire speed forwarding rates. The rates of duplex settings on both media are indistinguishable. This means that they comprise of two sets of transmitters, each with their medium-subordinate interfaces (when no information recording is essential) or their media-autonomous interfaces are combined consecutive in a double simplex manner. They can transport either half-duplex or full-duplex activity, however, both sides must match. Exchanging converters contain a system connection and can associate two half-duplex sections without joining their crash areas. These converters can typically be overseen by a system association or a neighborhood console.
Fast fiber converters are widely used wherever long network runs are required that exceed the 100 meters maximum segment length of traditional copper UTP/STP such as large Corporate or University campuses, large high rise buildings or Municipal buildings that cover a wide area or wherever ground loops or voltage spikes from lightning may be cause for concern. They can also be used in industrial/manufacturing facilities or in environments where the introduction of stray electrical signals are strictly regulated such as hospitals, clean rooms, and aircraft.
Showing all 11 results
GAOTek 10 Base-T to 10 Base-FL Ethernet Media ConverterID: GAO-EMC-104
This 10 Base-T to 10 Base-FL Ethernet Media Converter is specially designed to be used in remote locations using multimode and single mode fiber to deliver solid network performance and scalability.
GAOTek 10/100/1000M Media Converter (20 km)ID: GAO-EMC-101
This 10/100/1000 M Media Converter (20 km) is designed for media conversions which adopts switching technology and supports inter-conversion of electrical signals of 10/100/1000Base-T twisted pairs with optical signals of 1000Base-SX.
GAOTek 10/100/1000M media converter Ethernet Media ConverterID: GAO-EMC-102
This 10/100/1000M media converter Ethernet Media Converter is an Ethernet transmission equipment which supports 10/100M Ethernet fiber media converter and 10/100/1000M Ethernet fiber media converter simultaneously.
GAOTek Mini Gigabit Ethernet Media ConverterID: GAO-EMC-103
This Mini Gigabit Et
GAO Tek 16 Slot Media Converter ChassisID: C0340002tek
This 16 slot media converter chassis is used with card-type media converters.
GAOTek 100BASE-FX Fiber PCI Network Interface CardID: GAO-FMC-101
This interface card is for 100 Base-FX Fiber PCI network and features fiber connectors for a 100 Mbps IEEE 802.3u Ethernet network connection over optical fiber cable
GAOTek 1000M Fiber Optic Network Interface CardID: GAO-FMC-102
This Interface Card is for 1000 M Fiber Optic Network and features a mini-GBIC fiber connector (SFP) for a 1000 Mbps IEEE 802.3z Ethernet network connection over optical fiber cable
GAOTek 10/100Base-TX to 100Base-FX Media Converter with LFP FunctionID: GAO-FMC-103
This Media converter features 10/100 Base-TX to 100 Base-FX with LFP function and can easily track the network link failure and improves fiber-linking networks
GAOTek 10/100Base-TX to 100Base-FX Media ConverterID: GAO-FMC-104
This 10/100 Base-TX to 100 Base-FX Media Converter can convert 10/100 Mbps 10 BASE-T/100 BASE-TX Fast Ethernet twisted-pair signals to 100 BASE-FX Fast Ethernet fiber signals
GAOTek 1000 Base-TX to 1000 Base-FX Media ConverterID: GAO-FMC-105
This Gigabit Fiber Converter converts optical-electric ethernet signals between 1000M UTP interface (TX) and 1000M optical fiber interface (FX)
GAO Tek 10/100/1000 Base-TX to 1000 Base-FX Media ConverterID: GAO-FMC-106
This 10/100/1000 Base-TX to 1000 Base-FX Media Converter transforms 1000 Base-T (copper gigabit) media to 1000 Base-SX/LX (fiber gigabit) media and vice versa.